RL Vision Knowledge Base
Support questions and answers for software by RL Vision.
Note: This is an archived discussion. Any bug, problem or suggestion mentioned here is likely to have been fixed since it was written.
Subject: Re: Flash Renamer 6.3: Getting Overflow issue when using a preset
Date: Wed, 10 Feb 2010 19:03:51 +0100It's been slightly delayed, but only a few more days now. If you want, you can get the "released candidate" and try it out. It is very close to the final version. It would be good to verify that your problem has actually been solved.
http://www.rlvision.com/files/FlashRenamer64_Setup.exe
// Dan
Joren wrote:
> Hi
>
> Any target dates on when you plan to release the update that fixes the issue I reported last month (see email below). You mentioned that you are planning a release at the end of January but I haven't see anything announced in the website.
>
> Thanks,
> JR
>
> Date: Sun, 17 Jan 2010 17:10:17 +0100
> From: *****@*****
> To: *****@*****
> Subject: Re: Flash Renamer 6.3: Getting Overflow issue when using a preset
>
>
> Hello again,
>
> I think I have found the solution to the problem. I am working on an update, and plan to release it before the end of January. Make sure you get it!
>
> Thank you for reporting the bug to me!
>
> // Dan
>
>
> Joren wrote:
>
> Attached is a screen shot of the error.
>
> This is happening on any file. I'm using a 32 bit XP.
>
>
> Joren
>
> Date: Fri, 15 Jan 2010 20:15:58 +0100
> From: *****@*****
> To: *****@*****
> Subject: Re: Flash Renamer 6.3: Getting Overflow issue when using a preset
>
>
> Hello,
>
> The overflow message is shown in a messagebox. What is the title of this? (Does it contain the word "helper"?)
>
> Also, does this happen all the time, or just on specific files?
>
> Finally, do you have 32-bit or 64-bit XP?
>
> // Dan
>
>
> Joren wrote:
>
> Hi...
>
> I just installed and registered FR ver 6.31. I'm not able to use Pre-Sets when run from the Window Explorer shell extension. The error I get is "Run-Time error '6' Overflow"
>
> Can you help with this issue? I've tried to reinstall the software and the issue still persists. I'm using running it in Windows XP SP3.
>
> JR
>
http://www.rlvision.com/files/FlashRenamer64_Setup.exe
// Dan
Joren wrote:
> Hi
>
> Any target dates on when you plan to release the update that fixes the issue I reported last month (see email below). You mentioned that you are planning a release at the end of January but I haven't see anything announced in the website.
>
> Thanks,
> JR
>
> Date: Sun, 17 Jan 2010 17:10:17 +0100
> From: *****@*****
> To: *****@*****
> Subject: Re: Flash Renamer 6.3: Getting Overflow issue when using a preset
>
>
> Hello again,
>
> I think I have found the solution to the problem. I am working on an update, and plan to release it before the end of January. Make sure you get it!
>
> Thank you for reporting the bug to me!
>
> // Dan
>
>
> Joren wrote:
>
> Attached is a screen shot of the error.
>
> This is happening on any file. I'm using a 32 bit XP.
>
>
> Joren
>
> Date: Fri, 15 Jan 2010 20:15:58 +0100
> From: *****@*****
> To: *****@*****
> Subject: Re: Flash Renamer 6.3: Getting Overflow issue when using a preset
>
>
> Hello,
>
> The overflow message is shown in a messagebox. What is the title of this? (Does it contain the word "helper"?)
>
> Also, does this happen all the time, or just on specific files?
>
> Finally, do you have 32-bit or 64-bit XP?
>
> // Dan
>
>
> Joren wrote:
>
> Hi...
>
> I just installed and registered FR ver 6.31. I'm not able to use Pre-Sets when run from the Window Explorer shell extension. The error I get is "Run-Time error '6' Overflow"
>
> Can you help with this issue? I've tried to reinstall the software and the issue still persists. I'm using running it in Windows XP SP3.
>
> JR
>